Sika FerroGard-903 Plus Price in Pakistan

Name: Sika® FerroGard®-903 Plus
Brand: Sika
SKU: 16408

Sika® FerroGard®-903 Plus – Active corrosion inhibitor for reinforced concrete

Sika® FerroGard®-903 Plus is a surface applied active corrosion inhibitor, based on organic compounds, designed for use as an impregnation of steel reinforced concrete. It penetrates the concrete and forms a protective monomolecular layer on the surface of the reinforcing steel. Sika® FerroGard®-903 Plus both delays the start of corrosion and reduces the corrosion rate. Corrosion protection with Sika® FerroGard®-903 Plus increases the service and maintenance life cycles by up to 15 years when used as a part of a complete Sika Concrete Repair and Protection System.

Recommended Uses

For the corrosion protection of steel reinforced concrete structures above and below the ground.
As a corrosion control treatment for undamaged reinforced concrete where reinforcing steel is corroding, or is at risk from corrosion due to the effects of carbonated or chloride contaminated concrete.
Sika® FerroGard®-903 Plus is especially suitable for extending the service life of aesthetically valuable fair-faced concrete surfaces such as historic structures.

Technical Information

Verified performance data for Sika® FerroGard®-903 Plus, taken directly from the Sika Pakistan Product Data Sheet.

Chemical Base

Aqueous solution of amino alcohols & salts of amino alcohols

Appearance / Colour

Transparent liquid, colourless to slightly yellowish.

Density

~1.05 (at +20 °C)

pH-Value

~10

Viscosity

~20 mPa·s (Brookfield RVT, spindle 2, 100 rpm, 23 °C)

Consumption

Generally ~0.50 kg/m² (~480 ml/m²). For very dense concrete with low permeability, the rate of application of Sika® FerroGard®-903 Plus can be reduced but must not be lower than 0.300 kg/m² (290 ml/m²). To assess project

Ambient Air Temperature

+5 °C min. / +40 °C max.

Substrate Temperature

+5 °C min. / +40 °C max. Product Data Sheet Sika® FerroGard®-903 Plus May 2025, Version 03.01 020303040010000016

Standards

BRE, The use of surface applied Sika® FerroGard® 903 corrosion inhibitor to delay the onset of chloride induced corrosion in hardened concrete, BRE Client Report No. 224–346, 2005 Mott MacDonald, Evaluation of Sika® Ferr

Source: Sika Pakistan Product Data Sheet, Sika® FerroGard®-903 Plus (May 2025, Version 03.01; Sika article 020303040010000016), downloaded from pak.sika.com 2026-09-05. Price list 2023: SikaFerroGard-903 plus.

Packaging & Storage

Packaging

25 kg pail 220 kg drum

Storage

Store in a cool environment. In case of - frost (< -5 °C), - reversible crystallisation may occur. If this happens, let the product warm up at room temperature (+15 to +25 °C), then stir well to re-dissolve the crystals.

Shelf Life

24 months from date of production if stored properly in undamaged and unopened, original sealed packaging.

Application Guide (2 Easy Steps)

Application

SUBSTRATE QUALITY / PRE-TREATMENT The concrete shall be free from dust, loose material, surface contamination, existing renders, laitance, coatings, oil and other materials which reduce or prevent penetration. If the substrate is to be over-coated, the surface profile shall be sufficient to provide the required adhesion. De-laminated, weak, damaged and deteriorated concrete shall be repaired using Sika MonoTop ®, Sik

Cleaning of Tools

Use water to clean application equipment.

Follow the official Sika Technical Data Sheet for full application details.

Frequently Asked Questions

What is Sika® FerroGard®-903 Plus?

Sika® FerroGard®-903 Plus is a surface applied active corrosion inhibitor, based on organic compounds, designed for use as an impregnation of steel reinforced concrete. (Active corrosion inhibitor for reinforced concrete)

What packaging is available?

25 kg pail 220 kg drum

What is the shelf life?

24 months from date of production if stored properly in undamaged and unopened, original sealed packaging. Store in a cool environment. In case of - frost (< -5 °C), - reversible crystallisation may occur. If this happens, let the product warm up at room temperature (+15 to +25 °C), then stir well to re-dissolve the crystals.

View all questions

Reviews

There are no reviews yet.

Be the first to review “Sika® FerroGard®-903 Plus”

Technical documents

Data sheets for this product

Sika® FerroGard®-903 Plus
Product Data Sheet · May 2025, Version 03.01 · PDF 881 KB
Download PDF

More documents: Concrete Repair & Protection · Technical Library

Need Technical Advice or Current Price?

Sika® FerroGard®-903 Plus