Image on request
Concrete Repair & Protection · Concrete protection
Sika® FerroGard®-903 Plus
Active corrosion inhibitor for reinforced concrete
Sika TDS On demand
View product & data sheet Get price on WhatsApp
Concrete Repair & Protection · Concrete protection
Sikagard® PW
Sika TDS On demand
Available on order Not held in stock. Ask us for the current lead time and minimum order.
- Suitable for direct contact with Suitable for direct contact with potable water.
- Easy to clean Easy to clean, tough glossy finish.
- Very good resistance to a Very good resistance to a wide range of chemicals and corrosive vapours Sewage resistant.
- Good mechanical and chemical resistance Good mechanical and chemical resistance.
- High build High build.
Prices are quoted per project — no prices are shown online.
- Sika products supplierIslamabad & Rawalpindi.
- Get a quote on WhatsAppSend your product and quantity for current pricing.
- Technical support from MCTOur team helps you choose the right solution.
- DeliveryContact our team to confirm delivery and lead times to your location.
Product at a glance
Application thickness
Minimum two coats, each minimum 200 microns thick.
Pot life
~40 min. (20 °C)
Temperature range
+5 °C min. / +40 °C max.
Key benefits
- Suitable for direct contact with
- Easy to clean
- Very good resistance to a
- Good mechanical and chemical resistance
- High build
- Impervious to liquids
Sikagard® PW
Sikagard® PW is a two component, solvent free epoxy coating with outstanding mechanical and chemical properties. Suitable for use in hot and tropical climatic conditions.
Recommended uses
- Sikagard® PW may only be used by experienced professionals.
- Anti-corrosion coating on steel in food processing plants, sewage works, farms, agricultural enterprises, chemical and pharmaceutical facilities and beverage industry
Technical information
Technical information
Verified performance data for Sikagard® PW, taken directly from the Sika Pakistan Product Data Sheet.
| Chemical Base | Epoxy resin Please refer to local country price list for available packaging sizes: Part A 5.6 kg containers Part B1.4 kg containers Part A + B7 kg ready to mix units Part A 11.2 kg containers Part B 2.8 kg containers Pa |
|---|---|
| Appearance / Colour | Grey and white (mixed A + B), further colours upon request |
| Density | ~1.48 kg/l (25 °C) |
| Solid Content | ~100 % |
| Abrasion Resistance | ~50 mg (14 d / 23 °C)(CS 10 / 1000 / 1000) (ASTM D4060) |
| Tensile Adhesion Strength | > 1.5 N/mm 2 (or concrete failure) (ASTM C1583) |
| Consumption | ~0.3 kg/m 2 for a layer-thickness of 200 microns. This figure is theoretical and does not include for any additional material required due to surface porosity, surface profile, variations in level and wastage etc.. |
| Layer Thickness | Minimum two coats, each minimum 200 microns thick. |
| Ambient Air Temperature | +5 °C min. / +40 °C max. |
| Relative Air Humidity | < 80 % |
| Dew Point | Beware of condensation! The substrate and uncured floor must be at least 3 °C above dew point to reduce the risk of condensation or blooming on the floor finish. Note: Low temperatures and high humidity conditions increa |
| Substrate Temperature | +5 °C min. / +40 °C max. |
| Substrate Moisture Content | < 4 % pbw moisture content. Test method: Sika®-Tramex meter, CM-measurement or Oven-dry-method. No rising moisture according to ASTM (Polyethylene-sheet). |
| Pot Life | ~40 min. (20 °C) |
| Curing | Time Fully cured7 d (25 °C) |
| Waiting Time / Overcoating | Min. 4 h (35 °C) Min. 5 h (25 °C) Max. 2 d (25 °C) |
Source: Sika Pakistan Product Data Sheet, Sikagard® PW (May 2021, Version 02.01).
Packaging & storage
Packaging & storage
Packaging
1 / 3 Part A20 kg containers Part B5 kg containers Part A + B25 kg ready to mix units
Storage
Store in unopened, undamaged and sealed original packaging in dry conditions at temperatures between +5 °C and +30 °C. Protect from direct sunlight, heat and moisture.
Shelf life
12 months from date of production.
Application guide
Application guide (3 easy steps)
- Mixing / DosingRatio (A: B) = (4: 1) by weight
- ApplicationSUBSTRATE PREPARATION The substrate must be sound and of sufficient compressive strength (minimum 25 N/mm 2 ) with a minimum pull off strength of 1.5 N/mm 2 The substrate must be clean, dry and free of all contaminants such as dirt, oil, grease, coatings and surface treatments, etc. Concrete substrates must be prepared mechanically using abrasive blast cleaning or scarifying equipment to remove cement laitance and ac
- Cleaning of ToolsTools and equipment should be cleaned with Sika® Thinner immediately after use. Hardened material can only be removed mechanically.
Follow the official Sika Technical Data Sheet for full application details.
Technical documents
Data sheets for this product
More data sheets in Concrete Repair & Protection
FAQs
Frequently asked questions
What is Sikagard® PW?
Sikagard® PW is a two component, solvent free epoxy coating with outstanding mechanical and chemical properties.
What packaging is available?
1 / 3 Part A20 kg containers Part B5 kg containers Part A + B25 kg ready to mix units
What is the shelf life?
12 months from date of production. Store in unopened, undamaged and sealed original packaging in dry conditions at temperatures between +5 °C and +30 °C. Protect from direct sunlight, heat and moisture.
Quotation
Request a quotation for Sikagard® PW
Tell us the quantity and the site. We reply with price, lead time and the right pack size.
Technical advice
Need technical advice or current price?
Our team helps contractors and specifiers choose the right Sika solution and quote current pricing.
Chat on WhatsApp +92 300 5254439No prices are shown online — every quotation is prepared for the project.
Reviews
There are no reviews yet.